info@sundow.com    +86-536-8057068

产品展示

Centro de productos

posición actual: Casa > Centro de productos > Phenolic Resin

Phenolic Resin

Phenolic resin 2402 is a kind of thermoplastic phenolic resin synthesized from para-tert-butylphenol and formaldehyde by polycondensation in acidic medium.

Contáctanos Formato PDF
  • Introducción
  • Guía de selección
  • Aplicación

                                                                      WELLITETM Phenolic Resin for Adhesive

Instruction

Phenolic resin 2402 is a kind of thermoplastic phenolic resin synthesized from para-tert-butylphenol and formaldehyde by polycondensation in acidic medium. It is soluble in oil and can be blended with various kinds of synthetic rubber.

 

Chemical Name:                                                                

Para-tert-Butylphenol Formaldehyde Resin  

 

Molecular Formula:

(C11H14O) n

 

Molecular Structure:1678165724872342.jpg

 

 

Typical properties

Test item

Unit

Specification

Appearance

 /

Light yellow     lump

Specific gravity

g/cm3

1.08-1.12

Softening     point

90-115

Methylol content

%

8-12

Free phenol

%

≤2.0

Heating loss

%

≤0.5

Above is just part of our grades, if you want to know further information or more grades, please contact info@sundow.com. 


Application

1.       With good compatibility with chloroprene adhesive, it can be used to produce chloroprene rubber adhesive and it is especially applicable to the adhesive for shoes.

2.       It can be used as a curing agent for rubber such as butyl rubber, natural rubber, styrene-butadiene rubber (SBR), especially applicable to sulfurizing butyl rubber. 

3.       In coating industry, it can be used to produce end coating for external use, lacquer for floor, marine coating, antirust paint, water-based printing ink, and can be used as material of thin film anti-rust oil products.

 

Packing, transportation and storage

1.       Packing: using paper-plastic composite packaging and lined with pp bag, 25 kg/bag;

2.       Transportation: It is not dangerous material according to the transportation regulations.

3.       Storage: It should be stored in indoor, dry and ventilating place and protected from heat and fire. Recommended storage time from the date of analysis:12 months.

 

 

 

WELLITETM Phenolic Resin for Abrasive

Instruction

This series of phenolic resins are applied to bonded abrasives and are available in powder and liquid form. Due to strict formula design, effective molecular weight and distributing control method, the distribution of resin molecular reaches an ideally narrow status.

Ø  The powder resin is characterized in strong viscosity, mechanical strength, abrasion resistance, heat resistance and wet grinding stability.

Ø  The liquid resin has good wetting function, anti-moisture properties and well-distributed miscibility, and maintain high strength and grinding performance.


Properties

Ø  Powder form:

Grade

Appearance

Cure
  
  150(s)

Free     phenol
  
  %

Inclined     plate flow

125(mm)

Granularity

Application

AS-90

Light yellow

powder

90-120

1.5

40-60

99% under 
    200 mesh

General   ultra-thin disc

AS-50

50-85

2.0

30-45

High-strength   abrasion wheels

AS-70

70-80

1.0-2.5

20-35

More durable   than AS-50

Ø  Liquid form:

Grade

Viscosity
  
  25(cp)

Solid     content
  
  %

Solvent

Free     phenol
  
  %

Application

AS-650L

650-2000

72-80

water

10-14

Use with powder   grade

 Above is just part of our grades, if you want to know further information or more grades, please contact info@sundow.com. 


Packing, transportation and storage

Ø  Powder: Kraft paper bag with plastic liner inside, 25 kg/bag; Resin should be stored in a cool, dry and well-ventilated place. The storage life is 6 months, the color will become dark with the storage time, which will not affect the quality

Ø  Liquid form: 240kg/drum. Resin should be stored in a cool and well-ventilated slide gates below 20, far away from light. The common storage time: 2 months in winter and 1 month in summer.

Ø  Transportation: Both powder and liquid form phenolic resin are not dangerous material according to the transportation regulations.

 

 

WELLITETM Phenolic Resin for Casting

Instruction

This series of products are made by polycondensation and drying of phenol and formaldehyde. It has the advantages of below:

1.       The resin has high strength so that the amount added can be small, which can reduce the cost.

2.       Low gas generation, which can reduce casting porosity defects and improve yield.

3.       The resin has good flowability so it is easy to coat without any blind corner.

 

Properties

Grade

Appearance

Cure
  
  150(s)

Softening     point
  
  

Inclined     plate flow

125(mm)

Free     phenol
  
  %

Features

C-55

Yellow flake

55-65

85-95

70-110

2.0

High-strength

C-55E

50-70

85-95

70-110

3.0

Economic type of   C-55

 Above is just part of our grades, if you want to know further information or more grades, please contact info@sundow.com. 


Application

Including cast iron, ductile iron, ordinary cast steel, non-ferrous metal castings, casting coatings, and special coated sand for casting sand.

 

Packing, transportation and storage

Ø  Packing: Kraft paper bag with plastic liner inside, 25 kg/bag;

Ø  Transportation: It is not dangerous material according to the transportation regulations.

Ø  Storage: It should be stored in a cool, dry and well-ventilated place far away from heat source to avoid moisture and caking. Recommended storage time from the date of analysis: 6 months.

 

WELLITETM Phenolic Resin for Friction Material

 

Instruction

This series of phenolic resin, FR-50/FR-90/FR-70N, is applied into the brake lining/pad/shoes, clutch disc and all kinds of friction materials for motorcycles, farm vehicle, cars, heavy truck and train brake shoe etc. It is characterized in good friction performance, wide adjusting range of friction ratios and good recovery ability in high temperature.

 

Properties 

Grade

Appearance

Cure
    150
(s)

Free phenol
    %

Inclined plate   flow

125(mm)

Granularity

FR-50

 

Light yellow   powder

50-85

2.0

30-45

 

99% under 
    200 mesh

FR-90

90-120

1.5

40-60

FR-70N

70-80

1.0-2.5

20-35

 Above is just part of our grades, if you want to know further information or more grades, please contact info@sundow.com. 


Application

Ø  F-50: Economy grade for common use, general phenolic resin features with concentrated fineness distribution, excellent consistent and high bonding strength.

Ø  F-90: Compared with F-50, it has higher purity and bonding strength and the product made of it has lower friction loss and more stable friction coefficient.

Ø  F-70N: Modified by nitrile butadiene rubber and endows final product with better impact resistance.

 

Packing, transportation and storage

1.       Packing: Kraft paper bag with plastic liner inside, 25 kg/bag;

2.       Transportation: It is not dangerous material according to the transportation regulations.

3.       Storage: It should be stored in a cool, dry and well-ventilated place far away from heat source to avoid moisture and caking. Recommended storage time from the date of analysis: 6 months.

 

WELLITETM Phenolic Resin for Molding Compounds

Instruction

This series of resins can effectively control the roll hardening time with advanced processing, which is characterized in good insulation, heat and humidity resistance, dimensional stability and good molding range, and have good wetting ability with various polar fillers.

 

Properties

Grade

Appearance

Softening     point

Cure
  
  150(s)

Free     phenol
  
  %

Inclined     plate flow

125(mm)

Application

M-90

Light yellow

flake

90-100

90-100

2.5

45-75

General grade   for molding

M-100

100-110

100-110

2.5

40-70

High softening   point grade

 Above is just part of our grades, if you want to know further information or more grades, please contact info@sundow.com. 


Packing, transportation and storage

1.       Packing: Kraft paper bag with plastic liner inside, 25 kg/bag;

2.       Transportation: It is not dangerous material according to the transportation regulations.

3.       Storage: It should be stored in a cool, dry and well-ventilated place far away from heat source to avoid moisture and caking. Recommended storage time from the date of analysis: 6 months.